EXACTLY HOW TO SET UP A BATH TUB

Exactly How to Set up a Bath Tub

Exactly How to Set up a Bath Tub

Blog Article

Order Repair

Do you find yourself interested in critical information about How to Install a Bathtub Yourself?


How to Install a Bathtub Yourself
Installing a bathtub isn't precisely brain surgery, but it does require strong plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate immediately; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub and also set in the brand-new one. See to it you have actually certified yourself for the work and fit attempting it. Rather than working with a professional to take over a halfway-completed job, it is far better to think about using one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This post will certainly assist you mount a new tub in your washroom if you have actually already bought a new bathtub and also don't need to change the arrangement of your previous water system pipes.
Your tools and product list need to consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is detach the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the limited access that is frequently the case.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next off, place the tap in the installing hole in the bath/basin making sure that the washing machines are in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous kind should be attached to the tap finishes first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Installing the Bathtub


    Making use of both wood boards under its feet, put the tub in the called for setting. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small factors.
    The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the bathtub till the spirit level reads degree.
    To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
    Activate the water system and examine all joints and new pipework for leaks as well as tighten them if necessary. Load the tub as well as also inspect the overflow electrical outlet and the typical outlet for leakages.
    Ultimately, take care of the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the tub should wait till the bath tub has been utilized at the very least when as this will resolve it into its last setting.

    Preparing for the Installation


    Firstly, the supporting structure supplied with the bathroom must be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the tap features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to prevent strain on the bath tub.
    Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its last setting.

    Tiling Around the Tub


    In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a rigid seal, triggering the water to permeate the wall in between the bath and also the tiling, causing issues with moisture and feasible leakages to the ceiling listed below.
    You can select from a selection of coloured sealers to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always load the bath tub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealant can crack rather very early if you do not think about this motion prior to securing.
    Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof adhesive and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    As an avid person who reads on How to Install a Bathtub, I think sharing that piece of content was valuable. Please take a moment to share this article if you enjoyed reading it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.




    Visit Link


    Report this page